Your over-the-range microwave is humming but the food stays cold, or it threw sparks and a puff of smoke. Call Acdc Appliance Repair and we connect you with a licensed, insured independent pro near Temelec who services OTR, built-in and drawer microwaves.
A microwave is not a toaster. Inside the cabinet sits a high-voltage capacitor that can hold a lethal charge long after the plug is pulled, which is why this repair belongs with a trained technician and never with a screwdriver and a video.
We run a free referral line for homeowners. A dispatcher hears what the microwave is doing and connects you with an independent local technician who knows both the high-voltage side and the installation side of these units.
The contractors in our network are independent businesses that carry the license and insurance local rules require. Ask to see both at the door.
A magnetron or control board for a built-in can be a real expense. The technician writes the quote before any work starts, so you can compare it to a replacement unit and decide.
We look for a pro already working near Temelec. A same-day slot opens up regularly when local pros have breathing room, and the arrival window gets set while you are on the line.
Expect an insulated discharge tool for the capacitor, a multimeter for diode and transformer checks, the model tech sheet, and a microwave survey meter to check for leakage after high-voltage work.
This is the work we route for OTR, wall-mounted, drawer and convection combo microwaves. Every job starts by safely bleeding the capacitor before a single meter lead goes in.
Everything seems to run except the heating. That points to the high-voltage circuit: a failed magnetron, a shorted diode, an open capacitor, or a burnt transformer winding. The pro checks each part with a meter after bleeding the stored charge.
Sparking inside the oven often traces to a food-soaked waveguide cover, bare metal where the cavity paint chipped, or a worn rack support in a combo unit. Ignoring it can scorch the cavity and kill the magnetron.
Microwaves use a chain of door interlock switches plus a monitor switch. When a switch sticks, the monitor switch shorts the line on purpose and blows the line fuse, so the whole unit goes dark. A unit that runs with the door open needs to be unplugged right away.
Dead buttons, phantom beeps, or a unit that keeps running after the timer ends point to the membrane touchpad or a stuck relay on the control board. The technician reads the keypad circuit with a meter and checks the relays before ordering parts.
An over-the-range microwave also works as the range hood. Grinding fans, a lamp that never turns on, greasy metal filters, and a spent charcoal filter on recirculating installs all get handled here.
If the turntable sits still, the motor or the drive coupler is the likely culprit. An OTR microwave that tilts forward or shifts may have a loose mounting plate or top bolts that stripped the cabinet, and that needs attention before it drops onto the range.
Use this as a quick read before you call. Share what you see with the dispatcher, and the technician can bring the most likely parts.
| Symptom | Common cause | What the tech checks |
|---|---|---|
| Runs, light on, no heat | Magnetron, diode, capacitor or transformer failure | Each high-voltage part with the capacitor discharged |
| Completely dead, no display | Blown line fuse from a failed door switch | Fuse, interlock switches, monitor switch |
| Sparks or smoke inside | Burnt waveguide cover, chipped cavity paint | Cover, cavity surface, stirrer, rack supports |
| Keeps running at zero or with door open | Welded relay or failed interlock | Control board relays and door switch chain |
| Plate will not turn | Turntable motor or coupler | Motor continuity, coupler, roller ring |
| Vent fan loud or dead | Fan motor bearings, greasy filters | Fan motor, damper, grease and charcoal filters |
A basic countertop microwave usually is not worth a service call, and most technicians will tell you so on the phone. Over-the-range units, built-in wall models, drawer microwaves and convection combos are a different story. They cost more, they fit a cutout or bracket, and swapping one means trim kits, cabinet work and a vent connection.
Leave the cabinet closed and pick up the phone. The dispatch line is answered around the clock.
Let the dispatcher know if the unit is over-the-range, built-in, a drawer or a combo, and describe the symptom. The model number is usually on a sticker inside the door opening, and having it speeds up parts.
An independent technician working close to Temelec gets the job, and the dispatcher shares the arrival window. Same-day arrivals are routine when a local independent pro is free.
First comes a safe discharge of the capacitor, then meter tests on the magnetron, diode, transformer, door switches and board. An OTR unit sometimes has to be lifted off its mounting plate. The written, upfront quote comes before any work begins, and you decide.
After the repair, the pro heats a cup of water to confirm output and, after any high-voltage work, sweeps the door seal with a microwave survey meter to check for leakage. Written coverage for parts and labor is the norm among the pros we connect; ask for it.
Our over-the-range microwave went completely dark mid-popcorn. The technician found a blown line fuse, then traced it to a cracked door switch. He replaced both and showed me why the fuse would have blown again if he had only swapped the fuse.
Our wall-mounted microwave ran with no heat. Replacing it meant matching a trim kit, so I asked about repair. She tested the high-voltage parts, swapped the magnetron, and ran a leakage check with a survey meter before packing up.
Sparks were jumping off the side wall every time I warmed soup. It was a burnt waveguide cover soaked with grease. Quick fix, and he showed me how to keep that cover clean.
Our microwave drawer would not stop running after the timer hit zero. The pro found a welded relay on the control board, ordered the board by model number, and came back two days later to install it.
When the light, fan and turntable all work but food stays cold, the high-voltage circuit has failed. The most common causes are a bad magnetron, a shorted diode, an open capacitor, or a burnt transformer. These parts carry lethal voltage, so let a trained technician test them.
No. Stop using it until it is checked. Sparks usually come from a dirty or burnt waveguide cover or chipped cavity paint, and continued arcing can damage the magnetron. If there is smoke, keep the door closed and unplug it if you can reach the cord safely.
Most of the time a dead microwave has blown its line fuse, and the fuse blew because a door switch failed and the monitor switch tripped it. A good pro replaces the failed switch along with the fuse, not just the fuse.
Frequently. Over-the-range and built-in units are expensive and fitted to the opening, so a new one brings its own installation costs. Small countertop models are usually better replaced. With a written quote from the pro in hand, you can make the call.
We strongly advise against it. That capacitor stores enough energy to kill, even with the plug pulled. Keep the outer case on and leave the discharge to a technician with proper insulated tools.
Ask for it, especially after high-voltage or door work. Many pros sweep the door seal and vents with a microwave survey meter before they leave, to confirm the unit is sealed properly.
Our line connects homeowners and renters across Temelec and the surrounding area with independent microwave technicians. Calls go to whoever has a route nearby, and that matters when an over-the-range unit has to be taken down for service.
Someone answers around the clock. Calls after hours are typically scheduled for the first slot next morning, while daytime calls can become same-day visits when a nearby pro has room.
